- 1 LED filament
| Indice de rendu des couleurs | 90 |
| Température de couleur | Blanc chaud |
| Alimentation en mode marche (Pon) : | 7 W |
| Angle de faisceau | 300 ° |
| Stabilité de la couleur | 4 ≤ |
| Choix/réglage de la couleur lumineuse | Non |
| Consommation d'énergie en mode marche | 7 kWh/1000h |
| Classe d'efficacité énergétique (A à G) | E |
| Flicker pour LED et OLED MLS | 0,24 ≤ |
| Durée de vie L70B50 - LED et OLED | 15000 h |
| Effet stroboscopique pour LED et OLED MLS | 0,3 |
| Facteur de décalage pour Pon (min.) | 0,700 |
| Facteur de durée de vie (pour LED et OLED) | 0,9 |
| Facteur de maintien du flux lumineux (LED/OLED) | 93,11 % |
| Flux lumineux utile (Φ360) | 806 lm |
| Fréquence | 50 Hz |
| Indice de rendu des couleurs R9 | 57 |
| Rég. EAR N° | DE 38720470 |
| Source de lumière connectée (CLS) | Non |
| Source lumineuse | Non directionnel |
| Technologie d'éclairage utilisée | Ampoule LED |
| Tension d'entrée | 220-240 V |
| Classe IP | IP20 (Pièces sèches) |
| Compatible avec les variateurs | oui |
| Température de couleur | 2700 K |
| Douille | E 27 |
| Equivalente à une ampoule à incandescence de | 60 W |
| Particularité | LED-Filament |
| Design / Diameter / Height | Ampoule à filament / 60 mm / 105 mm |
| Température optimale | 25 °C |
| Type de variation | Variateur |
| Poids Net | 37 g |
| Voltage | 43 mA |
| Convient pour l'éclairage d'accentuation | Non - demi-angle entre 120 ° et 360 ° (Φuse) |
The LED light is designed for operation in open luminaires: the heat generated by the light during operation can therefore be emitted into the surroundings. The service life prognosis is based on this mode of operation. The service life is reduced by insufficient cooling when used in enclosed luminaires. Only use in lights intended for its use. Allow the light to cool down completely before changing it and switch off the power supply voltage. Damaged lights should be replaced immediately. No liability shall be assumed for damage caused by incorrect use.
Some dimmers can impair the function of the light (flickering, noise).
Mixed operation, i.e. the simultaneous operation of LED bulbs and standard incandescent bulbs or LED bulbs of different types on one dimmer cable, is not possible. If noises are heard with dimmers that were not noticed with incandescent bulbs: the dimmer is not suitable for LED bulbs.
Cable dimmers (dimmer integrated into the power cable) require a separate on/off switch since they may not be able to regulate right down to 0.
Note the dimmer's minimum load, otherwise it may not switch on or it may control the light incorrectly. Simple dimmers usually work from 60W to 400W.
With integrated dimmers that have a basic brightness setting, this must be set high enough otherwise the LED bulb may not switch on.
Dim slowly and evenly. Do not dim quickly or with jerky movements.
Only incandescent bulb dimmers are permitted - not dimmers for transformers, etc.
Touch dimmers are usually not suitable. Incorrect dimmers can permanently damage lighting.
